VBUS054DD-HS4 www.vishay.com vishay semiconductors rev. 1.0. 19-sep-11 1 document number: 83384 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 4-line bus-port esd protection marking (example only) dot = pin 1 marking x = date code y = type code (see table below) features ? ultra compact llp1010-5l package ? low package height < 0.4 mm ? 4-line usb esd-protection ? low leakage current ? low load capacitance c d = 0.8 pf ? esd-protection acc. iec 61000-4-2 15 kv contact discharge 15 kv air discharge ? pin plating nipdau (e4) no whisker growth ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec note ** please see document vishay material category policy: www.vishay.com/doc?99902 20896 20897 1 5 4 2 3 6 20932 xy ordering information device name ordering code taped units per reel (8 mm tape on 7" reel) minimum order quantity VBUS054DD-HS4 vbus54dd-hs4-g4-08 5000 5000 package data device name package name type code weight molding compound flammability rating moisture sensitivity level soldering conditions VBUS054DD-HS4 llp1010-6m c 1.07 mg ul 94 v-0 msl level 1 (according j-std-020) 260 c/10 s at terminals absolute maximum ratings parameter test conditions symbol value unit peak pulse current pin 1, 3, 4 or 5 to pin 2 or 6 acc. iec 61000-4-5; t p = 8 /20 s; single shot i ppm 3a peak pulse power pin 1, 3, 4 or 5 to pin 2 or 6 acc. iec 61000-4-5; t p = 8 /20 s; single shot p pp 57 w esd immunity contact discharge acc. iec 61000-4-2; 10 pulses v esd 15 kv air discharge acc. iec 61000-4-2; 10 pulses 15 kv operating temperature junction temperature t j - 40 to + 125 c storage temperature t stg - 55 to + 150 c
VBUS054DD-HS4 www.vishay.com vishay semiconductors rev. 1.0. 19-sep-11 2 document number: 83384 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? ratings at 25 c, ambient temperature unless otherwise specified. application note with the vbus54dd-hs4 a double, high speed usb-port or up to 4 other high speed signal or da ta lines can be protected against transient voltage signals. negative transients will be clamped close below the ground level while positive transients w ill be clamped close above the working ra nge. the high speed data lines, d 1 +, d 2 +, d 1 - and d 2 -, are connected to pin 1, 3, 4, and 5, pin 2 or 6 are connected to ground. as long as the signal voltag e on the data lines is between the ground- and the break down level, the low input capacitance of each channel offers a ve ry high isolation to ground an d to the other data lines. but a s soon as any transient signal exceeds this working range, th e VBUS054DD-HS4 clamps the transient to ground or to the avalanche break down voltage level. typical characteristics t amb = 25 c, unless otherwise specified fig. 1 - 8/20 s peak pulse current wave form acc. iec 61000-4-5 fig. 2 - esd discharge current wave form acc. iec 61000-4-2 (330 ? /150 pf) electrical characteristics (pin 1, 3, 4, or 5 to pin 2 or 6) parameter test conditions/remarks symbol min. typ. max. unit protection paths number of lines whic h can be protected n channel --4lines reverse stand-off voltage v rwm --5.5v reverse current at v in = v rwm = 5.5 v i r - < 0.01 0.1 a reverse breakdown voltage at i r = 1 ma v br 6.988.7v reverse clamping voltage at i pp = 3 a acc. iec 61000-4-5 v c -1619v forward clamping voltage at i f = 3 a acc. iec 61000-4-5 v f -3.54.5v capacitance v in = 0 v; any other i/o pin at 3.3 v c d -0.81pf v in = 2.5 v; any other i/o pin at 3.3 v - 0.5 0.8 pf 20897-1 1 5 4 2 3 6 t w i n u s b - p o r t d 2+ v bus gnd r e c e i v e r ic d 2- d 1+ d 1- 0 % 20 % 40 % 60 % 80 % 100 % 010203040 time ( s) i ppm 20 s to 50 % 8 s to 100 % 20548 0 % 20 % 40 % 60 % 80 % 100 % 120 % - 10 0 10 20 30 40 50 60 70 80 90 100 time (ns) discharge c u rrent i esd rise time = 0.7 ns to 1 ns 53 % 27 % 20557
VBUS054DD-HS4 www.vishay.com vishay semiconductors rev. 1.0. 19-sep-11 3 document number: 83384 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - typical capacitance c d vs. reverse voltage v r fig. 4 - typical forward current i f vs. forward voltage v f fig. 5 - typical reverse voltage v r vs. reverse current i r fig. 6 - typical peak clamping voltage v c vs. peak pulse current i pp fig. 7 - typical clampi ng performance at + 8 kv contact discharge (acc. iec 61000-4-2) fig. 8 - typical clampi ng performance at - 8 kv contact discharge (acc. iec 61000-4-2) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 v r ( v ) c d (pf) 0123456 f = 1 mhz pin 1, 3, 4 or 5 to pin 2 and 6 (one of pin 1, 3, 4 or 5 connected to 3.3 v ) 0.001 0.01 0.1 1 10 100 0.5 0.6 0.7 0.8 0.9 1.0 1.1 v f ( v ) i f (ma) pin 2 and 6 to pin 1, 3, 4, or 5 0 1 2 3 4 5 6 7 8 9 0.01 0.1 1 10 1 10 2 10 3 10 4 i r ( a) v r ( v ) pin 1, 3, 4 or 5 to pin 2 and 6 i pp (a) v c ( v ) - 5 0 5 10 15 20 01 2 3 4 meas u red acc. iec 61000-4-5 (8/20 s - w a v e form) v c pin 1, 3, 4 or 5 to pin 2 and 6 - 10 0 10 2030405060708090 t (ns) v c-esd ( v ) - 20 0 20 40 60 80 100 120 acc. iec 61000-4-2 + 8 k v contact discharge pin 1, 3, 4 or 5 to pin 2 and 6 - 100 102030405060708090 t (ns) v c-esd ( v ) - 20 0 20 40 60 80 100 120 140 160 180 acc. iec 61000-4-2 - 8 k v contact discharge pin 1, 3, 4 or 5 to pin 2 and 6
VBUS054DD-HS4 www.vishay.com vishay semiconductors rev. 1.0. 19-sep-11 4 document number: 83384 for technical questions, contact: esdprotection@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters (inches): llp1010-6m solder resist mask solder pad 0.125 (0.005) ref. 0.03 (0.001) 0 (0.000) pin 1 marking 0.4 (0.016) 0.33 (0.013) 0.35 (0.014) b sc 0.7 (0.028) ref. 0.22 (0.009) exp. dap 0.2 (0.008) 0.1 (0.004) 0.5 (0.020) exp. dap 0.25 (0.010) 0.15 (0.006) 1.05 (0.041) 0.95 (0.037) 1.05 (0.041) 0.95 (0.037) soldermask opening 0.03 meas u red middle of the package 0.05 (0.002) 0.175 (0.007) 0.35 (0.014) 0.7 (0.028) 0.35 (0.014) 0.3 (0.012) 0.22 (0.009) 0.5 (0.020) foot print recommendation: 20899 doc u ment no.:s8- v -3906.04-004 (4) re v . 4 - date: 09. sep. 2008 created - date: 17.j u ly.2007
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
